телефоны: +7(495) 760-70-69 , +7(916) 870-29-57

√Ћј¬Ќјя
 
ќ  ќћѕјЌ»»
 
ѕ–ќƒ” ÷»я
 
»Ќ‘ќ–ћј÷»я
 
÷≈Ќџ
 
 ќЌ“ј “џ
 
Ќќ¬ќ—“»
 
ј ÷»»
 

LMOG100-30

Digital Oil Control Valve

  • General
The LMOG100-30 electronic gear meter consists of an oval gear and its chamber with the appropriate connections to establish a controlled flow through the meter. The basic meter is made of the measuring element and of the housing. A 5-digit liquid crystal display, 4 units and battery indicator , accurate to the second decimal place, shows the exact amount of fluid dispensed. The unit is programmed at the factory to dispense and totalize in L, GAL, PT and QT. Low battery indicator is included. 3 buttons are included on the meter: УTotalФ, УResetФ, and УSetФ (underside the meter) Do not apply LMOG100-30 as a measuring tool for commercial trading
  • Before putting into operation
Please check that the technical data of the installation match with those of the lube meter. For example connections, pressure, flow range and medium. Once the meter has been installed, please make sure that no air pressure shocks or particles can damage the meter. Please check all connections to leakage. After the installation we recommend to do several transactions into an approved tank. Should the use of different oil viscosities show discrepancies by the error limit, this can immediately be corrected at the site as what follows:
  • Toggle УTotalФ and УResetФ at the same time. The display will show the current value of correction factor, please take it down.
  • Apply the following formula to decide the proper correction factor:
Proper correction factor= (actual value/displayed value) x current correction factor. eg. Actual value shown in the approved tank=0.9 QT Displayed value shown on the meter=1.000 QT Current correction factor =1.0100 Proper correction factor=0.9/1x1.0100=0.9090
  • Follow the instruction of item 4.5.1 of this manual to modify the correction factor.
  • Electronic register with LCD
The LCD register is connected to the bare meter with 4 screws. And a protector cover is connected to the bare meter with 4 screws. In the factory, a calibration factor is programmed, which has been determined on a hydraulic test bench. A 5-digit liquid crystal display, 4 units and battery indicator , accurate to the second decimal place, shows the exact amount of fluid dispensed. The unit is programmed at the factory to dispense and totalize in L, GAL, PT and QT. Low battery indicator is included.
  • Details of operation
4.1 Change the battery Battery Type: Lithium CR123A, 3V/1400 mAh A lithium battery supplies the unit and is built to last for 8 years of normal operation, which corresponds to approx. 500,000 litres (132,000 US GAL). When the battery signal is flashing on the display, a new battery should be changed. a) Remove the protector cover unscrewing the four screws. b) Change the battery with one of the same type and screw the lid on again. 4.2 Reset The display of the batch register memory can be put to ZERO by pushing the RESET button. A reset is not possible during a batch process. Resetting of the totalizer is only possible through internal programming. 4.3 Interruption of batch process By releasing the meter trigger, the batch process is interrupted. When pulled again, the batch process will be continued at the very point where it was interrupted, unless the RESET button has been pushed in the meantime. 4.4 Totalizer Pressing the TOTAL button will cause the accumulator memory value to be displayed, for as long as the button is being pressed. 4.5 Programming the meter 4.5.1 Modification of meter correction factor Introduction of function key SET is the key to activate programming mode, in the programming mode TOTAL button is used to choose desired digit or symbol RESET button is the switching key to add У1Ф to figures or symbols chosen When pressing SET button, figure for fluid totalized will be cleared automatically but meter correction factor and measurement unit will be remained. 4.5.2 Programming procedure by maintenance operator
  • Press SET button to activate programming mode
  • In programming mode, liquid display screen shows the correction factor 0.0000 and original measurement unit. The programmable correction factor has the range of 0.0000 to 9.9999. The decimal point is always located after the first digit. When the first digit У0Ф flashes, choose the digit by pressing УTotalФ button, add У1Ф by pressing RESET button and adjust the figure to be identical to УMeter correction factorФ.
  • Toggle УtotalФ button until the measurement unit sign flashes to activate switches among L, GAL, PT and QT. Press УSetФ button for 1 second to exit programming mode.
4.5.3. Modification process by end user If original measurement unit is GAL, PT or QT, it can be adjusted the measurement unit each other. End users can modify the measuring unit in use as what follows:
  • Press RESET button to clear the figure of current displayed quantity this time
  • Press TOTAL and RESET button at the same time for 5 seconds to activate programming mode, which shows GAL, PT or QT, measurement symbol set originally begins to flash.
  • Press RESET button to choose desired unit, the unit chosen begins to flash.
  • Press TOTAL button for 3 seconds to exit programming mode of measurement unit. Meanwhile, measurement unit of data memorized in total changes accordingly.
4.6 Installation procedure LMOG100-30 is equipped with a 1/2Ф (BSP/NPT) female thread on the inlet side. In order to obtain a leakage free connection from the meter to the hose, the hose end must have a 1/2Ф (BSP/NPT) male thread.
  • Clean both threads from fat.
  • Brush the 1/2Ф male thread at the hose with liquid sealant sealing. Please be careful that no sealing gets into the meter.
  • Screw both parts together.
Do not over-tighten the screw connection, otherwise the swivel of the meter could be damaged.
  • Technical data

English

Metric

Flow rate range

0-9 gpm

0-30 L/m

Operating Pressure (Maximum):

1500 psi

100 bar

Working Temperature:

14?F-+122?F

-10?C-+50?C

Accuracy(non-approved version)

±0.5%

±0.5%

Accuracy(approved version)

±0.3%

±0.3%

Applied Viscosity of Fluid

8-5000mPas

8-5000mPas

5-Digit LCD display

Quarts, Pints, Gallons

Liters

Inlet and outlet connections

1/2ФNPT

1/2ФBSP

 

English

Metric

Flow rate range

0-9 gpm

0-30 L/m

Operating Pressure (Maximum):

1500 psi

100 bar

Working Temperature:

14?F-+122?F

-10?C-+50?C

Accuracy(non-approved version)

±0.5%

±0.5%

Accuracy(approved version)

±0.3%

±0.3%

Applied Viscosity of Fluid

8-5000mPas

8-5000mPas

5-Digit LCD display

Quarts, Pints, Gallons

Liters

Inlet and outlet connections

1/2ФNPT

1/2ФBSP

    телефоны: +7(495) 760-70-69 , +7(916) 870-29-57